Click here to print this page

To see the animated tutorial visit: http://www.easy2diy.com/cm/easy/diy_ht_3d_index.asp?page_id=36156575

OVERVIEW

 

Wooden spindle back chairs are prone to taking a lot of abuse. People tend to shift around in their seats, slide the chair back and forth and even lean back on the hind legs of a chair. Over time, normal use can strain the joints and component parts of a chair to the point that joints and parts can break or loosen. If these problems are not addressed quickly, they can turn into bigger problems.

Individual loose joints and minor splits in the wooden parts can be taken care of with relative ease. However, if worse comes to worst you can completely disassemble a spindle back chair and rebuild it. You should only consider this if most of the joints on the chair are loose. And even then, you should not disassemble joints that still in good shape.

In this tutorial we will address minor and major repairs that you can make to a spindle back chair. Choose the techniques needed for your particular situation.


 

 

Skill Level & Time to Complete

  Time to Complete will depend on degree of repairs needed.
  • Beginner - - 
  • Intermediate - -
  • Advanced - -
  - A solid glue joint should not be disturbed. Try not to break solid joints as you repair loose ones.
  - Fix a loose joint or split pieces as soon as you discover it. Continued use of the chair can cause greater damage and cause other pieces to loosen or break.



SHOPPING LIST


Materials List
   Carpenter glue
   Wood blocks
   Wood dowel rods
   Wax paper
   Dental floss
 
Tools List
   Mallet
   C-clamps
   Bar clamps
   Tie down straps
   Drill
   Drill bits
   Screw drivers
   Fine paintbrush
   Syringe

 

1. Split rungs, rails or spindles.
To repair a split rung on a chair, lay the chair on its side so you can easily work on the damaged area. Take a piece of dental floss and coat it with carpenter’s glue. Work the floss into the split, coating both surfaces of the split area. Wipe off any glue on the chair’s finished surface.
2. Take two blocks of wood and sandwich the split in between them. Using a c-clamp, squeeze the blocks together around the split area. Wipe off any glue that oozes out of the split. Make sure the finished surfaces are flush. Let the glue set for 24 hours and remove the clamp. Flake off any dried glue on the finished surface of the chair.
3. Split platform.
If the platform (or seat) of the chair is split, gently pry the spit open and insert a small wedge in the spit to hold it open. Using a small artist’s paintbrush, coat the two sides on the split. Remove the small wedge.
4. Using bar clamps, squeeze the split closed. Use small blocks of wood to prevent the jaws of the clamp from marring the finished surface of the chair.
5. Loose joints.
If you have a few loose joints, a new glue job should tighten things up. Gently pull each joint apart so you can get a coat of glue inside the joint. Using an artist’s paintbrush, push glue into the joint. Alternatively, you can use a syringe and inject glue into the joint.

 

6. Clamp the joint together using a tie-down strap. Wrap it around the legs of the chair to pull the rails together.
7. If you are gluing spindle joints in the back of the chair, wrap it around the back and seat of the chair to pull the pieces together.
8. Rebuild a chair.
If you need to completely rebuild a spindle back chair, start by labeling all the pieces. Spindles, rungs and legs can vary in length and should go back to their original places. Remove any fasteners, such as screws and brackets. Drill out any dowels that are holding joints together. Using a mallet and a block of wood, tap apart all the joints. Once the chair is apart, fix and splits or damaged areas.
9. To reassemble the chair, start by gluing together the legs and rails. Use a tie-down strap to squeeze the pieces together. Then glue and assemble the chair seat. Use a block of wood and a mallet to tap it into position.
10.

Finally, assemble the back of the chair by gluing together the side rails, top rail and spindles. Use a tie-down strap to pull the chair back into the chair seat. Use a bar clamp to pull together the side rails and top rail.

Once all the glue has set, replace fasteners and dowels. Flake off any glue on the chair’s finished surface.

Copyright© 2001-2006 Easy2.com, Inc. All rights reserved.